What Priming Means for an Automatic Pool Cover Pump
After winter storage, a pool cover pump needs a quick setup check rather than traditional priming. Unlike manual pumps that require filling a line with water, automatic submersible models like the Hexago Automatic Swimming Pool Cover Pump use a float switch and a self-contained motor. The key is to ensure the pump is fully submerged, the discharge hose is connected correctly, and the check valve is installed to prevent backflow.
The Hexago 1/3HP pump is rated to move up to 2300 gallons per hour with a max head of 20 feet. It turns on automatically when it detects water at about 4/5" deep and shuts off when water drops to roughly 2/5". This means you do not need to manually prime it — you just need to place it correctly and confirm the connections are secure.
Step-by-Step Setup After Winter
Follow these steps to get your pool cover pump running after seasonal storage.
- Inspect the pump and cord: Check the 33-foot power cord for damage from winter conditions. Confirm the strainer base is clean and free of debris. The strainer base protects the pool cover, filters debris, and keeps the pump stable.
- Connect the discharge fittings: The pump comes with a 3/4" GHT elbow (90°), a 3/4" GHT quick connect, and a check valve. Attach the check valve to the pump outlet first — this prevents water from flowing back into the pump when it stops. Then connect the elbow and quick connect to your garden hose.
- Place the pump on the pool cover: Set the pump on the pool cover so the strainer base sits flat. The portable handle makes it easier to lift and position. Ensure the power cord reaches a GFCI-protected outlet without stretching.
- Submerge and allow automatic start: The pump will turn on automatically when water reaches about 4/5" deep. No manual priming is needed. If the pump does not start, check that the water level is high enough and the float switch moves freely.
Hexago Pool Cover Pump Specifications
- Hexago Automatic Swimming Pool Cover Pump, 1/3HP Submersible Water Pump with Check Valve Adapter & 33FT Power Cord, 2300GPH Water Removal Cover Pump for Pool, Hot Tubs, Rooftops and Water Beds: 1/3 HP pool cover pump moves up to 2300 gallons per hour with a max head of 20 feet. Confirms the pump can handle typical pool cover water removal without needing manual priming — the flow rate is sufficient for most residential covers.

Hexago Automatic Swimming Pool Cover Pump, 1/3HP Submersible Water Pump with Check Valve Adapter & 33FT Power Cord, 2300GPH Water Removal Cover Pump for Pool, Hot Tubs, Rooftops and Water Beds - Hexago Automatic Swimming Pool Cover Pump, 1/3HP Submersible Water Pump with Check Valve Adapter & 33FT Power Cord, 2300GPH Water Removal Cover Pump for Pool, Hot Tubs, Rooftops and Water Beds: Automatic on/off switch: turns on at 4/5" water depth, turns off at approximately 2/5". Explains why no manual priming is required. The pump self-activates once the cover collects enough water, then shuts off to prevent dry running.
- Hexago Automatic Swimming Pool Cover Pump, 1/3HP Submersible Water Pump with Check Valve Adapter & 33FT Power Cord, 2300GPH Water Removal Cover Pump for Pool, Hot Tubs, Rooftops and Water Beds: Includes 3/4" GHT elbow, 3/4" GHT quick connect, and a check valve. The check valve is critical after winter setup — it prevents water from siphoning back when the pump stops, which could cause air locks or restart issues.
Safety Checks Before First Run
The Hexago pump is UL Safety Listed and includes thermal overload protection that helps prevent dry burn damage. After winter, verify the pump is fully submerged before plugging it in. If the pump runs dry, the thermal overload will shut it off, but it is better to avoid that situation entirely.
Use a GFCI-protected outlet for the 33-foot power cord. The pump is designed for outdoor use on pool covers, tarps, hot tubs, rooftops, and similar flat surfaces. If the pump does not start after water reaches the activation level, check that the float switch is not stuck and that the check valve is installed in the correct orientation.
When the Pump Does Not Need Priming
Unlike centrifugal pumps that require water in the intake line, this submersible pump draws water directly through its strainer base. As long as the pump sits in water deep enough to cover the intake, it will operate. The automatic switch handles start and stop cycles without user intervention. After winter, the only priming-like step is confirming the hose is connected and the check valve is functional.
If you store the pump indoors during winter, reconnect the fittings and test it in a bucket of water before placing it on the pool cover. This confirms the automatic switch and check valve work correctly.


